Analysis and Design of Analog Integrated Circuits
(Sprache: Englisch)
ANALYSIS AND DESIGN OF ANALOG INTEGRATED CIRCUITS Authoritative and comprehensive textbook on the fundamentals of analog integrated circuits, with learning aids included throughout Written in an accessible style to ensure complex content can be appreciated...
Jetzt vorbestellen
versandkostenfrei
Buch (Gebunden)
148.60 €
- Lastschrift, Kreditkarte, Paypal, Rechnung
- Kostenlose Rücksendung
- Ratenzahlung möglich
Produktdetails
Produktinformationen zu „Analysis and Design of Analog Integrated Circuits “
Klappentext zu „Analysis and Design of Analog Integrated Circuits “
ANALYSIS AND DESIGN OF ANALOG INTEGRATED CIRCUITS Authoritative and comprehensive textbook on the fundamentals of analog integrated circuits, with learning aids included throughout Written in an accessible style to ensure complex content can be appreciated by both students and professionals, this Sixth Edition of Analysis and Design of Analog Integrated Circuits is a highly comprehensive textbook on analog design, offering in-depth coverage of the fundamentals of circuits in a single volume. To aid in reader comprehension and retention, supplementary material includes end of chapter problems, plus a Solution Manual for instructors. In addition to the well-established concepts, this Sixth Edition introduces a new super-source follower circuit and its large-signal behavior, frequency response, stability, and noise properties. New material also introduces replica biasing, describes and analyzes two op amps with replica biasing, and provides coverage of weighted zero-value time constants as a method to estimate the location of dominant zeros, pole-zero doublets (including their effect on settling time and three examples of circuits that create doublets), the effect of feedback on pole-zero doublets, and MOS transistor noise performance (including a thorough treatment on thermally induced gate noise). Providing complete coverage of the subject, Analysis and Design of Analog Integrated Circuits serves as a valuable reference for readers from many different types of backgrounds, including senior undergraduates and first-year graduate students in electrical and computer engineering, along with analog integrated-circuit designers.
Inhaltsverzeichnis zu „Analysis and Design of Analog Integrated Circuits “
Chapter 1 Models for Integrated-Circuit Active Devices 1 1.1 Introduction 1 1.2 Depletion Region of a pn Junction 1 1.2.1 Depletion-Region Capacitance 5 1.2.2 Junction Breakdown 7 1.3 Large-Signal Behavior of Bipolar Transistors 9 1.3.1 Large-Signal Models in the Forward-Active Region 9 1.3.2 Effects of Collector Voltage on Large-Signal Characteristics in the Forward-Active Region 14 1.3.3 Saturation and Inverse-Active Regions 16 1.3.4 Transistor Breakdown Voltages 21 1.3.5 Dependence of Transistor Current Gain ß F on Operating Conditions 24 1.4 Small-Signal Models of Bipolar Transistors 26 1.4.1 Transconductance 26 1.4.2 Base-Charging Capacitance 28 1.4.3 Input Resistance 29 1.4.4 Output Resistance 30 1.4.5 Basic Small-Signal Model of the Bipolar Transistor 30 1.4.6 Collector-Base Resistance 31 1.4.7 Parasitic Elements in the Small-Signal Model 31 1.4.8 Specification of Transistor Frequency Response 35 1.5 Large-Signal Behavior of Metal-Oxide-Semiconductor Field-Effect Transistors 39 1.5.1 Transfer Characteristics of MOS Devices 39 1.5.2 Comparison of Operating Regions of Bipolar and MOS Transistors 46 1.5.3 Decomposition of Gate-Source Voltage 48 1.5.4 Threshold Temperature Dependence 48 1.5.5 MOS Device Voltage Limitations 49 1.6 Small-Signal Models of MOS Transistors 50 1.6.1 Transconductance 51 1.6.2 Intrinsic Gate-Source and Gate-Drain Capacitance 52 1.6.3 Input Resistance 53 1.6.4 Output Resistance 53 1.6.5 Basic Small-Signal Model of the MOS Transistor 53 1.6.6 Body Transconductance 54 1.6.7 Parasitic Elements in the Small-Signal Model 55 1.6.8 MOS Transistor Frequency Response 57 1.7 Short-Channel Effects in MOS Transistors 60 1.7.1 Velocity Saturation from the Horizontal Field 60 1.7.2 Transconductance and Transition Frequency 64 1.7.3 Mobility Degradation from the Vertical Field 66 1.8 Weak Inversion in MOS Transistors 67 1.8.1 Drain Current in Weak Inversion 67 1.8.2 Transconductance and Transition Frequency in Weak Inversion 70 1.9 Substrate Current
... mehr
Flow in MOS Transistors 73 A.1.1 Summary of Active-Device Parameters 74 Problems 76 References 78 General References 79 Chapter 2 Bipolar, MOS, and BiCMOS Integrated-Circuit Technology 81 2.1 Introduction 81 2.2 Basic Processes in Integrated-Circuit Fabrication 82 2.2.1 Electrical Resistivity of Silicon 82 2.2.2 Solid-State Diffusion 83 2.2.3 Electrical Properties of Diffused Layers 85 2.2.4 Photolithography 87 2.2.5 Epitaxial Growth 89 2.2.6 Ion Implantation 90 2.2.7 Local Oxidation 90 2.2.8 Polysilicon Deposition 90 2.3 High-Voltage Bipolar Integrated-Circuit Fabrication 91 2.4 Advanced Bipolar Integrated-Circuit Fabrication 95 2.5 Active Devices in Bipolar Analog Integrated Circuits 98 2.5.1 Integrated-Circuit npn Transistors 99 2.5.2 Integrated-Circuit pnp Transistors 111 2.6 Passive Components in Bipolar Integrated Circuits 118 2.6.1 Diffused Resistors 119 2.6.2 Epitaxial and Epitaxial-Pinch Resistors 122 2.6.3 Integrated-Circuit Capacitors 124 2.6.4 Zener Diodes 124 2.6.5 Junction Diodes 125 2.7 Modifications to the Basic Bipolar Process 127 2.7.1 Dielectric Isolation 127 2.7.2 Compatible Processing for High-Performance Active Devices 128 2.7.3 High-Performance Passive Components 131 2.8 MOS Integrated-Circuit Fabrication 131 2.9 Active Devices in MOS Integrated Circuits 135 2.9.1 n-Channel Transistors 135 2.9.2 p-Channel Transistors 148 2.9.3 Depletion Devices 148 2.9.4 Bipolar Transistors 149 2.10 Passive Components in MOS Technology 150 2.10.1 Resistors 150 2.10.2 Capacitors in MOS Technology 152 2.10.3 Latchup in CMOS Technology 155 2.11 BiCMOS Technology 156 2.12 Heterojunction Bipolar Transistors 157 2.13 Interconnect Delay 160 2.14 Economics of Integrated-Circuit Fabrication 160 2.14.1 Yield Considerations in Integrated-Circuit Fabrication 161 2.14.2 Cost Considerations in Integrated-Circuit Fabrication 163 A.2.1 Spice Model-Parameter Files 166 Problems 167 References 170 Chapter 3 Single-Transistor and Multiple-Transistor Amplifiers 173 3.1 Device Model Selection for Approximate Analysis of Analog Circuits 174 3.2 Two-Port Modeling of Amplifiers 175 3.3 Basic Single-Transistor Amplifier Stages 177 3.3.1 Common-Emitter Configuration 178 3.3.2 Common-Source Configuration 182 3.3.3 Common-Base Configuration 186 3.3.4 Common-Gate Configuration 189 3.3.5 Common-Base and Common-Gate Configurations with Finite r o 191 3.3.6 Common-Collector Configuration (Emitter Follower) 195 3.3.7 Common-Drain Configuration (Source Follower) 198 3.3.8 Common-Emitter Amplifier with Emitter Degeneration 201 3.3.9 Common-Source Amplifier with Source Degeneration 204 3.4 Multiple-Transistor Amplifier Stages 206 3.4.1 The CC-CE, CC-CC, and Darlington Configurations 206 3.4.2 The Cascode Configuration 210 3.4.3 The Active Cascode 214 3.4.4 The Super Source Follower 216 3.5 Differential Pairs 219 3.5.1 The dc Transfer Characteristic of an Emitter-Coupled Pair 219 3.5.2 The dc Transfer Characteristic with Emitter Degeneration 221 3.5.3 The dc Transfer Characteristic of a Source-Coupled Pair 222 3.5.4 Introduction to the Small-Signal Analysis of Differential Amplifiers 225 3.5.5 Small-Signal Characteristics of Balanced Differential Amplifiers 228 3.5.6 Device Mismatch Effects in Differential Amplifiers 235 A.3.1 Elementary Statistics and the Gaussian Distribution 250 Problems 253 References 257 Chapter 4 Current Mirrors, Active Loads, and References 259 4.1 Introduction 259 4.2 Replica Biasing 259 4.3 Current Mirrors 261 4.3.1 General Properties 261 4.3.2 Simple Current Mirror 263 4.3.3 Simple Current Mirror with Beta Helper 269 4.3.4 Simple Current Mirror with Degeneration 270 4.3.5 Cascode Current Mirror 272 4.3.6 Wilson Current Mirror 283 4.4 Active Loads 287 4.4.1 Motivation 287 4.4.2 Common-Emitter-Common-Source Amplifier with Complementary Load 288 4.4.3 Common-Emitter-Common-Source Amplifier with Depletion Load 291 4.4.4 Common-Emitter-Common-Source Amplifier with Diode-Connected Load 293 4.4.5 Differential Pair with Current-Mirror Load 296 4.5 Voltage and Current References 309 4.5.1 Low-Current Biasing 309 4.5.2 Supply-Insensitive Biasing 315 4.5.3 Temperature-Insensitive Biasing 327 A.4.1 Matching Considerations in Current Mirrors 338 A.4.1.1 Bipolar 338 A.4.1.2 Mos 340 A.4.2 Input Offset Voltage of a Differential Pair with Active Load 343 A.4.2.1 Bipolar 343 A.4.2.2 Mos 345 Problems 348 References 353 Chapter 5 Output Stages 355 5.1 Introduction 355 5.2 The Emitter Follower as an Output Stage 355 5.2.1 Transfer Characteristics of the Emitter-Follower 356 5.2.2 Power Output and Efficiency 359 5.2.3 Emitter-Follower Drive Requirements 366 5.2.4 Small-Signal Properties of the Emitter Follower 366 5.3 The Source Follower as an Output Stage 368 5.3.1 Transfer Characteristics of the Source Follower 368 5.3.2 Distortion in the Source Follower 370 5.3.3 Transfer Characteristics of the Super Source Follower 374 5.4 Class B Push-Pull Output Stage 378 5.4.1 Transfer Characteristic of the Class B Stage 378 5.4.2 Power Output and Efficiency of the Class B Stage 381 5.4.3 Practical Realizations of Class B Complementary Output Stages 385 5.4.4 All-npn Class B Output Stage 392 5.4.5 Quasi-Complementary Output Stages 394 5.4.6 Overload Protection 397 5.5 CMOS Class AB Output Stages 399 5.5.1 Common-Drain Configuration 399 5.5.2 Common-Source Configuration with Error Amplifiers 401 5.5.3 Alternative Configurations 408 Problems 415 References 420 Chapter 6 Operational Amplifiers with Single-Ended Outputs 421 6.1 Applications of Operational Amplifiers 422 6.1.1 Basic Feedback Concepts 422 6.1.2 Inverting Amplifier 423 6.1.3 Noninverting Amplifier 425 6.1.4 Differential Amplifier 425 6.1.5 Nonlinear Analog Operations 426 6.1.6 Integrator, Differentiator 427 6.1.7 Internal Amplifiers 428 6.2 Deviations from Ideality in Real Operational Amplifiers 436 6.2.1 Input Bias Current 437 6.2.2 Input Offset Current 437 6.2.3 Input Offset Voltage 438 6.2.4 Common-Mode Input Range 438 6.2.5 Common-Mode Rejection Ratio (cmrr) 439 6.2.6 Power-Supply Rejection Ratio (psrr) 440 6.2.7 Input Resistance 441 6.2.8 Output Resistance 442 6.2.9 Frequency Response 442 6.2.10 Operational-Amplifier Equivalent Circuit 442 6.3 Basic Two-Stage MOS Operational Amplifiers 443 6.3.1 Input Resistance, Output Resistance, and Open-Circuit Voltage Gain 444 6.3.2 Output Swing 446 6.3.3 Input Offset Voltage 446 6.3.4 Common-Mode Rejection Ratio 450 6.3.5 Common-Mode Input Range 451 6.3.6 Power-Supply Rejection Ratio (psrr) 453 6.3.7 Effect of Overdrive Voltages 458 6.3.8 Layout Considerations 459 6.3.9 Amplifier with Level Shifting in the Input Stage 462 6.4 Two-Stage MOS Operational Amplifiers with Cascodes 465 6.5 MOS Folded-Cascode Operational Amplifiers 467 6.6 MOS Telescopic-Cascode Operational Amplifiers 471 6.7 Replica Biasing of the Tail Current Source 475 6.8 MOS Active-Cascode Operational Amplifiers 489 Problems 492 References 498 Chapter 7 Frequency Response of Integrated Circuits 499 7.1 Introduction 499 7.2 Single-Stage Amplifiers 499 7.2.1 Single-Stage Voltage Amplifiers and the Miller Effect 499 7.2.2 Frequency Response of the Common-Mode Gain for a Differential Amplifier 511 7.2.3 Frequency Response of Voltage Buffers 513 7.2.4 Frequency Response of Current Buffers 527 7.3 Multistage Amplifier Frequency Response 531 7.3.1 Dominant-Pole Approximation 531 7.3.2 Zero-Value Time Constant Analysis 532 7.3.3 Cascade Voltage-Amplifier Frequency Response 537 7.3.4 Cascode Frequency Response 541 7.3.5 Frequency Response of a Current Mirror Loading a Differential Pair 548 7.3.6 Short-Circuit Time Constants 549 7.3.7 Weighted Zero-Value Time Constants 554 7.4 Relation Between Frequency Response and Time Response 563 7.5 Pole-Zero Doublets 565 7.5.1 Effect of a Pole-Zero Doublet on Settling Time 565 7.5.2 Frequency Dependence of a Cascode Current-Source Load 570 7.5.3 Frequency Dependence of an Active-Cascode Current-Source Load 572 7.5.4 Doublet in a Differential Amplifier with Mismatch 574 Problems 575 References 584 Chapter 8 Feedback 585 8.1 Ideal Feedback Equation 585 8.2 Gain Sensitivity 587 8.3 Effect of Negative Feedback on Distortion 587 8.4 Feedback Configurations 589 8.4.1 Series-Shunt Feedback 589 8.4.2 Shunt-Shunt Feedback 592 8.4.3 Shunt-Series Feedback 594 8.4.4 Series-Series Feedback 595 8.5 Practical Configurations and the Effect of Loading 595 8.5.1 Shunt-Shunt Feedback 596 8.5.2 Series-Series Feedback 602 8.5.3 Series-Shunt Feedback 611 8.5.4 Shunt-Series Feedback 617 8.5.5 Summary 620 8.6 Single-Stage Feedback 620 8.6.1 Local Series-Series Feedback 622 8.6.2 Local Series-Shunt Feedback 624 8.7 The Voltage Regulator as a Feedback Circuit 626 8.8 Feedback Circuit Analysis Using the Return Ratio 632 8.8.1 Closed-Loop Gain Using the Return Ratio 634 8.8.2 Closed-Loop Impedance Formula Using the Return Ratio 640 8.8.3 Summary--Return-Ratio Analysis 646 8.9 Modeling Input and Output Ports in Feedback Circuits 646 Problems 649 References 656 Chapter 9 Frequency Response and Stability of Feedback Amplifiers 657 9.1 Introduction 657 9.2 Relation Between Gain and Bandwidth in Feedback Amplifiers 657 9.3 Instability 659 9.3.1 The Nyquist Criterion 659 9.3.2 Phase Margin and Gain Margin 661 9.3.3 Stability of the Super Source Follower 666 9.4 Compensation 671 9.4.1 Theory of Compensation 671 9.4.2 Methods of Compensation 676 9.4.3 Two-Stage MOS Amplifier Compensation 681 9.4.4 Compensation of Single-Stage CMOS Op Amps 693 9.4.5 Nested Miller Compensation 696 9.5 Root-Locus Techniques 705 9.5.1 Root Locus for a Three-Pole Transfer Function 705 9.5.2 Rules for Root-Locus Construction 708 9.5.3 Root Locus for Dominant-Pole Compensation 718 9.5.4 Root Locus for Feedback-Zero Compensation 719 9.6 Slew Rate 723 9.6.1 Origin of Slew-Rate Limitations 723 9.6.2 Methods of Improving Slew Rate in Two-Stage Op Amps 725 9.6.3 Improving Slew Rate in Bipolar Op Amps 728 9.6.4 Improving Slew Rate in MOS Op Amps 729 9.6.5 Effect of Slew-Rate Limitations on Large-Signal Sinusoidal Performance 733 9.7 Effect of Feedback on a Pole-Zero Doublet 734 A.9.1 Analysis in Terms of Return-Ratio Parameters 736 A.9.2 Roots of a Quadratic Equation 737 Problems 739 References 746 Chapter 10 Nonlinear Analog Circuits 747 10.1 Introduction 747 10.2 Analog Multipliers Employing the Bipolar Transistor 747 10.2.1 The Emitter-Coupled Pair as a Simple Multiplier 748 10.2.2 The dc Analysis of the Gilbert Multiplier Cell 750 10.2.3 The Gilbert Cell as an Analog Multiplier 752 10.2.4 A Complete Analog Multiplier 755 10.2.5 The Gilbert Multiplier Cell as a Balanced Modulator and Phase Detector 756 10.3 Phase-Locked Loops 760 10.3.1 Phase-Locked Loop Concepts 760 10.3.2 The Phase-Locked Loop in the Locked Condition 762 10.3.3 Integrated-Circuit Phase-Locked Loops 771 10.4 Nonlinear Function Synthesis 775 Problems 777 References 779 Chapter 11 Noise in Integrated Circuits 781 11.1 Introduction 781 11.2 Sources of Noise 781 11.2.1 Shot Noise 781 11.2.2 Thermal Noise 785 11.2.3 Flicker Noise (1/f Noise) 786 11.2.4 Burst Noise (Popcorn Noise) 787 11.2.5 Avalanche Noise 787 11.3 Noise Models of Integrated-Circuit Components 789 11.3.1 Junction Diode 789 11.3.2 Bipolar Transistor 790 11.3.3 MOS Transistor 791 11.3.4 Resistors 798 11.3.5 Capacitors and Inductors 799 11.4 Circuit Noise Calculations 799 11.4.1 Bipolar Transistor Noise Performance 802 11.4.2 Equivalent Input Noise and the Minimum Detectable Signal 805 11.4.3 MOS Transistor Noise Performance 807 11.5 Equivalent Input Noise Generators 812 11.5.1 Bipolar Transistor Noise Generators 813 11.5.2 MOS Transistor Noise Generators 818 11.6 Effect of Feedback on Noise Performance 820 11.6.1 Effect of Ideal Feedback on Noise Performance 821 11.6.2 Effect of Practical Feedback on Noise Performance 821 11.7 Noise Performance of Other Transistor Configurations 828 11.7.1 Common-Base-Stage Noise Performance 828 11.7.2 Emitter-Follower Noise Performance 829 11.7.3 Differential-Pair Noise Performance 830 11.7.4 Super-Source-Follower Noise Performance 833 11.8 Noise in Operational Amplifiers 836 11.9 Noise Bandwidth 840 11.10 Noise Figure and Noise Temperature 845 11.10.1 Noise Figure 845 11.10.2 Noise Temperature 849 Problems 849 References 854 Chapter 12 Fully Differential Operational Amplifiers 857 12.1 Introduction 857 12.2 Properties of Fully Differential Amplifiers 857 12.3 Small-Signal Models for Balanced Differential Amplifiers 860 12.4 Common-Mode Feedback 865 12.4.1 Common-Mode Feedback at Low Frequencies 867 12.4.2 Stability and Compensation Considerations in a CMFB Loop 871 12.5 CMFB Circuits 873 12.5.1 CMFB Using Resistive Divider and Amplifier 873 12.5.2 CMFB Using Two Differential Pairs 878 12.5.3 CMFB Using Transistors in the Triode Region 880 12.5.4 Switched-Capacitor CMFB 882 12.6 Fully Differential Op Amps 885 12.6.1 A Fully Differential Two-Stage Op Amp 885 12.6.2 Fully Differential Telescopic-Cascode Op Amp 896 12.6.3 Fully Differential Folded-Cascode Op Amp 897 12.6.4 A Differential Op Amp with Two Differential Input Stages 898 12.6.5 Neutralization 899 12.7 Unbalanced Fully Differential Circuits 901 12.8 Bandwidth of the CMFB Loop 907 12.9 Analysis of a CMOS Fully Differential Folded-Cascode Op Amp 909 12.9.1 dc Biasing 911 12.9.2 Low-Frequency Analysis 914 12.9.3 Frequency and Time Responses in a Feedback Application 920 Problems 927 References 933 Index 935
... weniger
Bibliographische Angaben
- Autoren: Paul R. Gray , Paul J. Hurst , Stephen H. Lewis , Robert G. Meyer
- 2024, 6. Auflage, 976 Seiten, Maße: 26,1 x 18,3 cm, Gebunden, Englisch
- Verlag: Wiley John + Sons
- ISBN-10: 1394220065
- ISBN-13: 9781394220069
- Erscheinungsdatum: 15.02.2024
Sprache:
Englisch
Kommentar zu "Analysis and Design of Analog Integrated Circuits"
Schreiben Sie einen Kommentar zu "Analysis and Design of Analog Integrated Circuits".
Kommentar verfassen